ZGX Series Regenerative AC/DC Source and Load
_____
ESA Series Bidirectional(Regenerative) AC Power Supply
_____
ESD Series Bidirectional(Regenerative) DC Power Supply
_____
KGS Series Bidirectional(Regenerative) AC Power Supply
_____
· Customized power, voltage and current ranges
· Grid Simulator, 4-Quadrant operation (-R Option)
· Independent 3-phase output
· Sequence programming
· Up to 50th harmonic waveform generation
· HVRT, LVRT, continous ride through test support
· Island mode for anti-island test
· ON/OFF phase angel programmable
· Current limit mode for short circuit test
· TTL trigger signal available with voltage or frequency change
· DC output (-DC option)
· Regenerative eLoad, electronic RLC load (-LD Option)
· Line impedance (R and L) simulation （-IMP Option）
· Add single phase output（-1P Option）
· Watercooling（-W Option）
· Master/Salve interface for power extension（-MS Option）
· Extend to higher output frequency（only CV mode）（-HFXXX Option）
· Soft start
· Custom waveforms (sine, clipped sine wave, rectified wave)
· TFT touch screen
· LAN and RS485 interfaces
· Optional analog interface（-ATI Option）
· Mod-bus/SCPI
· Local and remote emergency stop
· Remote sense
· CE conformity
· Compact modular design, 15KVA in 4U
· Bi-directional design
· Output: AC, DC, AC+DC
· Single unit: maximum 15KW, 450V L-N, 30A/ph, DC-1KHz output
· Single phase, 3-phase, split phase, and multi-channel output
· Various modes: Regenerative AC/DC source, regenerative AC/DC load, BiPolar DC source
· Regenerative RLC load in full frequency range
· True current source in CC mode
· Up to 100th harmonics waveform generation, inter-harmonic generation
· Soft start: effectively restrain the impulse current when power on
· Trigger out, TTL signal output for voltage or frequency change
· Error locating function
· LAN interface
· MOD-bus /SCPI protocols
· 24 months warranty
· Single system up to 500kW, up to 4MW and above
· Output voltage up to 2000V(std)
· Applications: battery simulation, battery test (-BSS option), PV simulation (-PV option)
· Program accuracy up to 0.1%
· Seamless transition between source and sink modes (-R option)
· Current rise time (0 -90%) <1ms (-BSS option)
· Soft start: effectively restrain the impulse current when power on
· CC/CV/CP/CR mode available
· Regenerative DC load function (-LD option)
· Hardware & software for PV Simulation (-PV option)
· Low-Voltage operation mode (-ZV option)
· Master-Slave interface (-MS option)
· Use water-cooling (-W option)
· LAN/RS485 interfaces (standard)
· CAN/RS232/ATI interfaces (-CAN/-232/-ATI option)
· Emergency stop button and indicators on front panel
· TFT-Touch panel operation
· Mod-bus/SCPI protocols
· Output terminal insulation monitoring function (-INS option)
· Output contactor
· Remote sense
· CE conformity
· 13 months warranty
· Modular design, output power from 15kVA to 1080kVA
· Bi-directional AC/DC power source, seamless transition between source and sink modes
· Regenerative AC/DC load function
· Output: AC, DC, AC+DC
· Independent three-phase output, which can be configured as single-phase output
· Max output 450V L-N within output frequency range from DC to 5kHz
· Frequency Range: DC~ 5kHz max
· Up to 100th harmonic waveform generation, inter-harmonic generation
· Trigger out, TTL signal output for voltage or frequency change
· AC output, ON/ OFF output phase angle can be programmed
· Using true current feedback control when working in CC mode
· RLC Load Simulation&RCD Load Simulation
· Current limit can be programmed, output can be shorted for short circuit test
· Bi-Polar DC Source (-BP option)
· Analog signal input for use as a power amplifier (delay ≤ 20 µs)
· 30 Built-in harmonic waveforms
· Soft start: effectively restrain the impulse current when power on
· TFT-Touch panel operation
· Master-Slave interface
· LAN, RS485, Analog control interface
· Emergency stop button and indicators on front panel
· Mod-bus/ASCII protocols
· CE conformity
· 13 months warranty
BSL Series High Power DC Power Supply/E-Load
_____
Regenerative DC electronic Load
_____
Regenerative AC electronic Load
_____
· ESD series with -LD option can be used as regenerative DC electronic load. DC load simulation includes constant current, constant resistance, constant voltage, and constant power modes.
· ESD series DC electronic load with -ZV option can produce large current that meets the requirements under the input condition close to 0.4V, which can evaluate the electrical characteristics of the fuel cell (such as VI), etc.
ESA/KGS series can be used as regenerative AC electronic load. This function consists of CR mode, Rectifier mode, CC/CP phase lead/lag mode. CR mode is used to simulate three-phase resistive loads, the CR mode and three-phase resistance parameters can be set through the panel and can realize the program of resistance sequence. Rectifier mode can be used to simulate non-linear loads, the CC/CP mode and CF (setting range: 1.414~3) parameters can be set through the panel. CC/ CP phase lead/lag mode can simulate sinusoidal current, Constant current CC and constant power CP modes are available to adjust load current or power, phase angle can be set from 90° to -90° simulating the voltage and current conditions under inductive and capacitive loads.
· Output Power: 100kW/150kW/200kW/250kW/300kW
· Output Voltage: 1000V/1500V/2000V
· Output Current: *2 / *3 / *4
· Auto-Ranging Output
· Soft start: effectively restrain the impulse current when power on
· Seamless transition between source and sink modes
· Current rise time (0% -90%) <5ms
· CC/CV/CP/CR mode available
· Regenerative DC load function
|
|